EasternLogic UMC4
user manual

Контроллер EasternLogic UMC4 инструкция по подключению и настройке лазерного станка

Содержание 

1-1 SPECIFICATION
1-2 APPEARANCE
1-3 LAYOUT
2. PIN ASSIGNMENT
2-1 LASER CONTROL CONNECTOR
2-1-1 P1 (SCANHEAD)：XY2-100 INTERFACE PORT
2-1-2 P2 (LASER CONNECTOR)：LASER CONTROL PORT
2-1-3 P3 (RS232)：PLC COMMUNICATION PORT
2-1-4 P4 (I/O CONNECTOR)：ROTARY, ENCODER AND I/O PORT
3. INSTALLATION AND CABLE CONNECTION

3-1 UMC4 INSTALLATION

3-2 XY2-100 DIGITAL SCANNER
3-3 PULSE/DIRECTION SIGNAL CONNECTION
3-3-1 DIFFERENTIAL SIGNAL
3-3-2 COMMON ANODE TTL

3-3-3 COMMON CATHODE TTL

3-4 AXIS CONTROL SIGNAL CONNECTION
3-4-1 COMMON CATHODE SENSOR(NPN)

3-4-2 COMMON ANODE SENSOR(PNP)

3-5 TTL SIGNAL CONNECTION
3-6 ENCODER SIGNAL CONNECTION

3-7 PHOTO COUPLE SIGNAL CONNECTION
3-7-1 OPTO IN CONNECTION
3-7-2 OPTO OUT CONNECTION
3-8 START & STOP SIGNAL CONNECTION
3-8-1 CONNECT WITH GENERAL BUTTONS
3-8-2 CONNECT WITH SENSORS
3-8-3 INPUT TTL SIGNAL
3-9 HWCONFIG SETTING DESCRIPTION
3-9-1 SCANNER ALIGNMENT：SET P1 (XY2-100).
3-9-2 DAC SETTING：SET P2 (ANALOG OUT VOLTAGE).
3-9-3 INPUT SENSOR TYPE：SET P2、P4(START、STOP).
3-9-4 EXTENSTION
3-9-5 SIGNAL POLARITY (ENABLE ACTIVE LOW)

4. OTHERS

4-1 CLOCK

4-1-1 HARDWARE CONFIGURATION
4-1-2 SOFTWARE CONFIGURATION (TIME REFLASH)

4-2OFFLINE MARKING SIGNAL TIME SERIES
4-3 FILE SELECTION FOR OFF-LINE MARKING

4-3-1 THROUGH PLC HUMAN-MACHINE INTERFACE

4-3-2 THROUGH EXTERNAL I/O
4-4 LED STATUS (D1 ~ D8)

5. UMC4_B_SPI BOARD(SPI G3 / G4)
5-1 APPEARANCE
5-2 PIN ASSIGNMENT
5-2-1 J4~J7 (LASER EXTEND CONNECTOR)

5-3 LED STATUS
6. UMC4_B_IPG BOARD(TYPE D / D1) (ALSO APPLY FOR RAYCUS AND JPT LASER)

6-1 APPEARANCE
6-2 PIN ASSIGNMENT
6-2-1 J4~J5 (LASER EXTEND CONNECTOR)
6-3 LED STATUS
7. UMC4_B_MOTION
7-1 APPEARANCE 7-1-1 UMC4_B_MOTION_SPI：(SPI G3 / G4)
7-1-2 UMC4_B_MOTION_IPG：(IPG TYPE D / D1)
7-2 PIN ASSIGNMENT
7-2-1 P1 LASER CONTROL CONNECTOR
7-2-2 P2~P4 CONTROL PORT
7-2-3 JF1 (INPUT): TTL INPUT PORT
7-2-4 JF2(OUTPUT): TTL OUTPUT PORT
7-2-5 J4~J7 (LASER EXTEND CONNECTOR)
7-2-6 JF4~JF6 SENSOR CONTROL PORT：(TERMINAL BLOCK)

7-2-7 D1~D19 LASER LED STATUS DESCRIPTIONS
7-2-8 D20~D46 MOTION LED STATUS
7-3 CABLE CONNECTION
7-3-1 PULSE/DIRECTION SIGNAL CONNECTION
7-3-2 CONNECT WITH SENSORS
7-3-3 ENCODER SIGNAL CONNECTION7-3-4 TTL SIGNAL CONNECTION (JF1、JF2)
7-3-5 SPI STATUS SIGNAL CONNECTION (J6、J7)
8 OMRON LASER

8-1 DRIVERS SETTING
8-2 CABLE CONNECTION

9 USING RS-232
9-1 WHAT IS RS-232
9-2 SETTING TO USE RS-232 TO CONTROL LASER
APPENDIX1: VARIOUS LASER SETTING MODES
TYPE 1：CO2 MODE
TYPE2：YAG 1、2、3 MODE
TYPE 3：R05 MODE
APPENDIX2：HOW TO CONNECT WITH PLC
APPENDIX3：PLC ADDRESS DEFINITION TABLE